Atlas Automotive Equipment

Atlas Air Force AF10-3PH 10HP 120-Gallon Air Compressor

In stock

SKU: ATEMPAF10-3PH

$5,399.00

Delivery Option

Warehouse Pickup Ship to My Address

Why Shop With Us?

✓ Authorized Dealers
✓ FREE & FAST Shipping: In Stock and Ready to Ship
✓ No Sales Tax (Exl MO Residents)
✓ Questions? Call Team Member: (620)202-7711

Description

The Atlas Air Force AF10 is a 10HP two-stage commercial air compressor built on a 120-gallon horizontal steel tank made in the USA. Its 3-cylinder pump delivers 37 CFM at 90 PSI and 35 CFM at 175 PSI, with a working range of 145–175 PSI. It is sized for busy automotive shops, body shops, and high-throughput service facilities where several technicians draw air at the same time and a smaller single-stage compressor can’t keep up with sustained demand.

The AF10 ships with the Atlas Plus Package: an air-cooled aftercooler, automatic low-oil shut-off, and automatic tank drain. These three features extend pump life, knock condensate out of the air on its way to the tank, and remove tank water without manual valve cycling. The unit runs on 220V, 3-phase service through an included magnetic starter that buffers the motor against electrical input swings.

Atlas AF10 air compressor labeled diagram with 72-inch length and 52-inch height, showing air filters, aftercooler, 10 HP 1750 RPM motor, magnetic starter, pressure relief valve, and auto water drain valve — Component layout, 72″ long × 52″ tall.

Plus Package

Air-cooled aftercooler

The aftercooler sits between the pump and the tank. Compressed air leaves the pump hot and full of water vapor; the aftercooler drops the air temperature before it reaches the tank, which condenses moisture into liquid that the tank drain removes. Tools downstream see drier air, which is the difference between a paint job that flashes evenly and one that fish-eyes.

Atlas AF10 aftercooler heat exchanger close-up with finned core and braided supply hoses — Aftercooler core with braided supply lines.

Automatic low-oil shut-off

An oil-level sensor on the pump cuts power if the oil drops below the safe operating level. Catastrophic compressor failures most often start with low oil running through a hot pump; this sensor takes the failure mode off the table.

Atlas AF10 low-oil shut-off sensor with sight glass mounted on the compressor pump above the maintenance instructions label — Low-oil shut-off with sight glass on the pump.

Automatic tank drain

A timer-controlled solenoid drain opens on a programmable interval to purge condensate from the tank. The dials set on-seconds (how long the valve opens) and off-minutes (interval between drains), so the shop can tune it to local humidity without anyone having to crack the manual drain at the end of every day.

Features

2-stage, 3-cylinder pump — staged compression for higher delivered CFM at working pressure than a single-stage of equivalent horsepower.
10 HP motor, 1,750 RPM — belt-driven, sized for continuous commercial duty.
120-gallon horizontal steel tank, made in the USA — large reserve flattens pressure dips during heavy tool use.
Magnetic starter included — protects the motor from line-voltage fluctuation and adds to overall unit longevity.
Continuous run option — removes start-stop surge cycles from the motor when air demand stays high.
Heavy-duty metal belt guard — protects belt drive from debris and incidental contact.
Vibro-isolation pad set — reduces vibration transfer into the floor.
Finned tank inlet tube — sheds heat between aftercooler and tank for reduced tank-water accumulation.
Hands-free tank drain extension — routes the drain valve to an accessible location.
Compressor oil drain extension tube — makes scheduled oil changes a tube-into-bucket job rather than a contortion under the pump.

What’s Included

Atlas Air Force AF10 compressor (motor, 2-stage pump, 120-gallon horizontal tank)
Plus Package: aftercooler, automatic low-oil shut-off, automatic tank drain
Magnetic starter
Set of vibro-isolation pads
Hands-free tank drain extension
Compressor oil drain extension tube
Heavy-duty metal belt guard

Specifications

Atlas Air Force AF10 Specifications
Motor	10 HP, 1,750 RPM
Pump	3-cylinder, 2-stage
Air Outlet Size	3/4″ NPT
Delivered CFM @ 90 PSI	37
Delivered CFM @ 175 PSI	35
Pressure Setting	145–175 PSI
Tank Capacity	120 gallons, horizontal, made in USA
Overall Dimensions	L 72″ × W 32″ × H 52″
Shipping Weight	1,000 lbs
Electrical	220V, 3-phase, 30 A breaker required
Wire	10-gauge recommended, 70 ft max run from breaker
3-phase service is a hard requirement — this unit will not run on single-phase power. Verify your shop’s service before ordering, or call 307-381-1810 to confirm fit.

Warranty

1-year parts warranty on the AF10 compressor.

FAQ

What electrical service does the AF10 need?

220V three-phase with a 30-amp breaker. Atlas recommends 10-gauge wire and a maximum 70-foot run from the breaker to the unit. This compressor will not run on single-phase service.

Is the tank made in the USA?

Yes — the 120-gallon horizontal steel tank is manufactured in the USA.

What does the Plus Package include?

Three features bundled with every AF10: an air-cooled aftercooler that drops air temperature before the tank, an automatic low-oil shut-off that protects the pump from running dry, and an automatic tank drain that purges condensate on a programmable interval.

What is the warranty?

1-year parts warranty on the compressor.

What CFM should I expect at shop pressure?

37 CFM delivered at 90 PSI and 35 CFM delivered at 175 PSI. The compressor cycles between 145 and 175 PSI.

What is included in the box?

The AF10 ships with the Plus Package (aftercooler, low-oil shut-off, auto tank drain), a magnetic starter, vibro-isolation pads, a hands-free tank drain extension, a compressor oil drain extension tube, and the heavy-duty metal belt guard.

Documents

Manual and technical documents available on request.

Your Auto Lift ships on a LTL common carrier freight company. It is taken to your location on a 48 foot semi truck. Please note the following before making your purchase:

You are responsible for unloading the lift from the truck. The truck driver does not unload it for you.

Lift Gate delivery service is not available for auto lifts.

You cannot unload an auto lift from the truck by hand. You must have machinery that can lift the full weight on your auto lift for unloading from the truck. Fork Lift, Bobcat, Tractor, Tow Truck, Back Hoe are all good options.

If you cannot unload from a truck, we can ship to our carrier's nearest freight terminal for you to pickup with a trailer or moving van.

You are responsible for calling the freight company to make a delivery appointment. We don't know your schedule so we can't do this for you.

Free shipping does not include shipping to Government Secure Locations, State and National Parks, Construction Sites, Islands, Alaska or Hawaii.

When your lift ships, we will email you the carrier information and tracking number. Freight shipping is slower than small package shipping and can take 3-14 days depending on your location so please be patient.

Cancellations & Refunds: At Car Lift Nation, we pride ourselves on having the best return policies in the industry. Cancel your order any time before it ships completely free of charge (exceptions apply such as custom orders, see below).

If you have questions, please send an email to support@carliftnation.com or call us at (620)202-7711.

Cancellations (Before Order Ships)

If you need to cancel an order, please contact us as soon as possible so we can refund you in full before your order leaves the warehouse. Reach agents during business hours at (620)202-7711, the chat in the bottom right, or email support@carliftnation.com any time.

Cancellations of Custom Orders

Custom or made to order products cannot be canceled or refunded as these products are put into production specifically for your order.

These units are custom made to your specification or created once you order. Once you place your order they start building your unit. Your warranty will guarantee you a fully functional and operational product. If it is not clear whether your order is custom or made to order, please message or call us.

All sales are final for Custom made and Made to order products.

Refunds and Returns

If you need to exchange your product, you may do so. You, as the customer, are responsible for any shipping costs throughout any returns and exchange processes.

Not all orders are available for return once they have shipped. We order our products directly from the manufacturer. Therefore, if the manufacturer will not permit us to return a product, we cannot offer you a return. This often varies on a case-by-case basis; please reach out to us if you would like specific information on your brand and/or product.

Due to increasing LTL/freight shipping costs, any outright returns will incur a 25% cancellation fee + return shipping costs. If you are replacing the product with something else, we may be able to help you cover some of the costs depending on the product.

Customers have 30 days from the date they received the item to initiate a return, however, please check the specific return policy for the brand of product you are purchasing as the brand specific return policy on the product page overrides this general return policy of 30 days.